732
edits
No edit summary |
No edit summary |
||
(45 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
'''TRANSCENDENTAL LIE-DETECTOR''' | '''TRANSCENDENTAL LIE-DETECTOR''' | ||
[[File:Graaaphics.png| | [[File:Graaaphics.png|600px]] | ||
For my project under the Term ''Observe Experiment Connect'' I | |||
helps me to | For my project under the Term ''Observe Experiment Connect'' I build a device that | ||
my environment. For this purpose, sensors | helps me to understand and perceive | ||
are sewn | my environment better. For this purpose, sensors (light, gas, temperature) | ||
are sewn into a WEARABLE which will collect specific values | |||
from different circumstances. I measure my | from different circumstances. I measure my | ||
own electrical currents to observe whether | own electrical currents to observe whether | ||
different circumstances have an influence on | different circumstances have an influence on | ||
my body. | my body. when a intersection of the measured data occurs, it will be experienced (vibration). | ||
[[File:Armband.JPG|300px]][[File:Backpack.JPG|300px]] | |||
[[File:Backpack2.JPG|300px]][[File:Ohrring.JPG|300px]] | |||
[[File:Ring.JPG|300px]][[File:Stirnband.JPG|300px]] | |||
[[File:Elektroniksens.jpeg|600px]] | |||
[[File:Atriummmi.JPG|200px]][[File:Baahnhof.JPG|200px]][[File:BAhnhoff.JPG|200px]] | |||
[[File:Barfusss.JPG|200px]][[File:Flyyy.JPG|200px]][[File:Nahkauff.JPG|200px]] | |||
[[File:Rolltreppe.JPG|200px]][[File:Showoff.JPG|200px]][[File:Steinesteine.JPG|200px]] | |||
[[File:Steubenstraße.JPG|200px]][[File:Tiefgarage.JPG|200px]][[File:Tunnelll.JPG|200px]] | |||
[[File:Waaaasser.JPG|200px]][[File:Wasssssser.JPG|200px]][[File:Zeitschrifttt.JPG|200px]] | |||
[[File:Aframe.JPG|200px]] | |||
In many cultures, as in science, it is believed | In many cultures, as in science, it is believed | ||
Line 24: | Line 43: | ||
am creating and moving. | am creating and moving. | ||
{{#ev:vimeo|755708631}} | |||
Due to my personal upbringing in the antroprosophic movement, I was inspired by it. The project is created around the believes of it. | |||
[[ | |||
'''REALIZATION''' | |||
[[File:Illustrt.jpg|600px]] | |||
'''The Device''' | '''The Device''' | ||
[[File:fully1.jpg|600px]] | |||
Line 50: | Line 73: | ||
*A dress that is inspired by the belives of the antroprosophical movement | *A dress that is inspired by the belives of the antroprosophical movement | ||
*A output that demonstrates the connecting moment | *A output that demonstrates the connecting moment | ||
Line 55: | Line 79: | ||
''Electronics'' | ''Electronics and Arduino Code'' | ||
To measure the environmental values, a light sensor, a gas sensor and a temperature sensor are connected to an Arduino Nano. The values of these are compared with those of the ground sensor (Sensor by Martin Howse). Then, when these values overlap, the output, a vibration is triggered at a vibration module. | To measure the environmental values, a light sensor, a gas sensor and a temperature sensor are connected to an Arduino Nano. The values of these are compared with those of the ground sensor (Sensor by Martin Howse). Then, when these values overlap, the output, a vibration is triggered at a vibration module. | ||
#define vibOutPin 4 //Vibrationsmotor als Konstante "vibOutPin" an Digitalpin 4 | |||
int bodyPin = A0; | |||
int lightPin = A1; | |||
int tempPin = A2; | |||
int gasPin = A3; | |||
int bodyVal,lightVal,tempVal,gasVal = 0; //Variablen "___Val" global definieren | |||
int tempDiff,lightDiff,gasDiff = 0; //Variablen für Differenz zwischen "bodyVal" und "___Val" | |||
void setup() { | |||
pinMode(vibOutPin, OUTPUT); //Pin für Output definieren | |||
Serial.begin(9600); //Geschwindigkeit für serielle Übertragung bestimmen | |||
} | |||
void loop() { | |||
bodyVal = analogRead(bodyPin); | |||
Serial.print ("Body: "); | |||
Serial.print(bodyVal); | |||
Serial.print(" == "); | |||
lightVal = analogRead(lightPin); | |||
Serial.print( "Licht: "); | |||
Serial.print(lightVal); | |||
Serial.print(" || "); | |||
tempVal = analogRead(tempPin); | |||
Serial.print ("Temperatur: "); | |||
Serial.print(tempVal); | |||
Serial.print(" || "); | |||
gasVal = analogRead(gasPin); | |||
Serial.print("Gas: "); | |||
Serial.print(gasVal, DEC); | |||
Serial.print(""); | |||
Serial.println(" || "); | |||
lightDiff = lightVal - bodyVal; | |||
tempDiff = tempVal - bodyVal; | |||
gasDiff = gasVal - bodyVal; | |||
Serial.print("Difference: "); | |||
Serial.print(lightDiff); | |||
Serial.print(" || "); | |||
Serial.print(tempDiff); | |||
Serial.print(" || "); | |||
Serial.println(gasDiff); | |||
Serial.println(""); | |||
if (tempDiff >= -50 && tempDiff <= 50 || lightDiff >= -50 && lightDiff <= 50 || gasDiff >= -50 && gasDiff <= 50) | |||
{ | |||
digitalWrite(vibOutPin,HIGH); | |||
delay(4000); | |||
digitalWrite(vibOutPin, LOW); | |||
} else { | |||
digitalWrite(vibOutPin, LOW); | |||
} | |||
delay(30000); | |||
} | |||
''Harness'' | ''Harness'' | ||
Line 72: | Line 155: | ||
*Does need the measurements of the electronics but must be flexible for sudden change of electronics | *Does need the measurements of the electronics but must be flexible for sudden change of electronics | ||
*(Water resistant) | *(Water resistant) | ||
Additionally a bracelet is made to attach and wear the vibration motor. Because the light sensor should not be influenced by my shadows a headband is necessary. | |||
Line 87: | Line 171: | ||
'' | [[/'''WORK IMPRESSIONS''']] | ||
[[ | [[/'''REFERENCES +INSPIRATION''']] |
edits