GMU:Devices of Perception/Francis and Paul: Difference between revisions

From Medien Wiki
Line 83: Line 83:


[[File:Assignment3.jpg|608px]]  
[[File:Assignment3.jpg|608px]]  
<br> We used the same circuit twice to run the two motors


ASTABLE 555 - RESISTORS as SWITCHES
ASTABLE 555 - RESISTORS as SWITCHES
Line 95: Line 97:
[[File:Pres3.jpg|200px]]
[[File:Pres3.jpg|200px]]
<br> Parts:
<br> Parts:
2x
<br>
Double Pole Double Throw - Relay
2x Double Pole Double Throw - Relay |
TIP 122
TIP 122 |
555 Timer
555 Timer | <br>
3x Battery
3x Battery




<br><videoflash type=vimeo>101011710|610|340</videoflash>
<br><videoflash type=vimeo>101011710|610|340</videoflash>

Revision as of 18:17, 17 July 2014

DEVICES OF PERCEPTION

BASICS

SYMBOLS.jpg 555 sheet.jpg Decade Counter sheet.jpg




ASSIGNEMENT N° 1 - LOUDNESS KILL SWITCH

Assignement1.jpg

MONOSTABLE 555 - MOMENTARY SWITCH

The "Loudness Kill Switch" reacts to the loudness of music emmited from a speaker. The mechanical construction consists of an aluminium ball applied to a loudspeaker, moving towards a copper rod when music is played. The circuit will be closed if the aluminium ball gets in contact with the copper rod. That happening a LED will light up and the loudspeaker (connected to an amplifier again connected to a solid state relay) will turn off for ca. 30 seconds. This time passed the loudspeaker will turn on as the LED will turn off again.


SKETCH.jpg BALL AND CIRCUIT.JPG
555 TIMER ON BREADBOARD.JPG AMPLIFIER.jpg SOLID STATE RELAY.JPG BALL AND ROD.JPG


Parts: Styrofoam ball wrapped with aluminium foil | Copper rod | 555 Timer | Solid State Relay | Loudspeaker | Amplifier



ASSIGNEMENT N° 2 - VEHICLE, MODEL N° 1

Assignement2 1.jpg

ASTABLE 555 - PHOTODIODE as a SWITCH

For the second assignment we decided to built a kind of vehicle. One that should be able to move forwards, backwards and sidewards. Therefore we came up with the idea to use two motors with plastic wheels as our main device. The first model was able to move forwards and backwards depending on a photodiode and its changing resistance again depending light.

To improve: Apply a second photodiode to the breadboard so that it is possible to steer both of the wheels independent from each other.


Ass2 3.jpg Ass2 2.jpg Ass2 1.jpg

Parts: 1x Double Pole Double Throw - Relay | TIP 127 | 741 Comparator | Photodiode | 2x Battery |




ASSIGNEMENT N° 3 - DRAWING MACHINE

Assignment3.jpg
We used the same circuit twice to run the two motors


ASTABLE 555 - RESISTORS as SWITCHES VEHICLE, MODEL N° 2, DRAWING MACHINE The basis for our third assignment was the previous one. Instead of the photodiode's resistance triggering the Double Pole Double Throw - Relay, we decided to only work with the common resistors and capacitors as our aim was to make the vehicle move in a certain rhythm. We added another Double Pole Double Throw - Relay, two 555 Timers and two TIP 122 to the breadboard. This allowed us to control both of the motors separately from each other.

To improve: Add photodiodes so that you can influence the rhythm of the motors moving forwards/backwards permanently.

Pres4.jpg Pres2.jpg Pres3.jpg
Parts:
2x Double Pole Double Throw - Relay | TIP 122 | 555 Timer |
3x Battery



<videoflash type=vimeo>101011710|610|340</videoflash>