364
edits
→The printer queue
| (5 intermediate revisions by the same user not shown) | |||
| Line 65: | Line 65: | ||
|animationcycle01.bfb (Frame 1-4) | |animationcycle01.bfb (Frame 1-4) | ||
|26.8. | |26.8. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx 140 minutes | ||
| | | | ||
| | | | ||
| Line 77: | Line 77: | ||
|animationcycle02.bfb (Frame 5-7 +12) | |animationcycle02.bfb (Frame 5-7 +12) | ||
|30.8. | |30.8. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx 140 minutes | ||
| | | | ||
| | | | ||
| Line 89: | Line 89: | ||
|animationcycle03.bfb (Frame 8-11) | |animationcycle03.bfb (Frame 8-11) | ||
|31.8. | |31.8. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx 140 minutes | ||
| | | | ||
| | | | ||
| Line 101: | Line 101: | ||
|animationcycle04.bfb (Frame 13-14) | |animationcycle04.bfb (Frame 13-14) | ||
|1.9. | |1.9. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx. 60 minutes | ||
| | | | ||
| | | | ||
| Line 113: | Line 113: | ||
|animationcycle05.bfb (Frame 15-16) | |animationcycle05.bfb (Frame 15-16) | ||
|2.9. | |2.9. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx. 60 minutes | ||
| | | | ||
| | | | ||
| Line 125: | Line 125: | ||
|zoetrope_cap.bfb (cap of the zoetrope) | |zoetrope_cap.bfb (cap of the zoetrope) | ||
|15.9.-16.9. | |15.9.-16.9. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx. 10 hours till abortion | ||
| | | | ||
|imprecise printbed complicates printing of large objects (20x20x1cm), ABS warps too much (high temperature?) | |imprecise printbed complicates printing of large objects (20x20x1cm), ABS warps too much (high temperature?) | ||
| Line 137: | Line 137: | ||
|zoetrope_cap.bfb (cap of the zoetrope) | |zoetrope_cap.bfb (cap of the zoetrope) | ||
|21.9. | |21.9. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx. 20 minutes | ||
| | | | ||
|problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop | |problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop | ||
| Line 161: | Line 161: | ||
|zoetrope_cap_pla.bfb (cap of the zoetrope with pla settings) | |zoetrope_cap_pla.bfb (cap of the zoetrope with pla settings) | ||
|28.9.-29.9. | |28.9.-29.9. | ||
| | | | ||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
| | |approx. 8hours | ||
| | | | ||
|structure was a bit week and the material feed was blocked due to mechanical problems with the PLA material roll (approx 30minutes of printing without material(!), cause the extrusion was kind of blocked) | |structure was a bit week and the material feed was blocked due to mechanical problems with the PLA material roll (approx 30minutes of printing without material(!), cause the extrusion was kind of blocked) | ||
| Line 173: | Line 173: | ||
|zoetrope_lamp.bfb (construction for the led lamp) | |zoetrope_lamp.bfb (construction for the led lamp) | ||
|29.9. | |29.9. | ||
| | |||
|Robert S. und Florian M. | |||
| | |||
|approx. 2hours | |approx. 2hours | ||
| | |||
|everything went perfectly fine | |||
| | |||
|[[File:Lamp.jpg|right|thumb|150px|]] | |||
|- | |||
| | |||
|crankhandle_p1.bfb (part of the gear) | |||
|13.10. | |||
| | |||
|Robert S. und Florian M. | |||
| | |||
|approx. 20 minutes | |||
| | |||
|everything went perfectly fine | |||
| | |||
|[[File:Crank_handle_part1.JPG|right|thumb|150px|]] | |||
|- | |||
| | |||
|gearshell.bfb (part of the gear) | |||
|26.10. | |||
| | |||
|Robert S. und Florian M. | |Robert S. und Florian M. | ||
| | | | ||
|several hours (only troubleshooting | |||
| | |||
|problems with the printbed level (was too close to extruder), flakes of PLA were sometimes extruded together with the ABS | |||
|leveling the bed, cleaning the extruder | |||
|no acceptable result, therefore nothing to photography | |||
|- | |||
| | | | ||
|gearshell2.bfb (part of the gear) | |||
|9.11. | |||
| | |||
|Robert S. und Florian M. | |||
| | |||
|approx. 3,5hours | |||
| | | | ||
|everything went perfectly fine | |everything went perfectly fine | ||
| | | | ||
|[[File: | |[[File:Gearshell.JPG|right|thumb|150px|]] | ||
|} | |} | ||