GMU:3DIY/Printer queue: Difference between revisions

← Older edit

GMU:3DIY/Printer queue (view source)

Revision as of 21:57, 9 November 2010

1,480 bytes added , 9 November 2010

→‎The printer queue

Olif2166

364

edits

@@ Line 65: / Line 65: @@
 |animationcycle01.bfb (Frame 1-4)
 |26.8.
-|approx 140 minutes
+|
 |Robert S. und Florian M.
 |
-|
+|approx 140 minutes
 |
 |
@@ Line 77: / Line 77: @@
 |animationcycle02.bfb (Frame 5-7 +12)
 |30.8.
-|approx 140 minutes
+|
 |Robert S. und Florian M.
 |
-|
+|approx 140 minutes
 |
 |
@@ Line 89: / Line 89: @@
 |animationcycle03.bfb (Frame 8-11)
 |31.8.
-|approx 140 minutes
+|
 |Robert S. und Florian M.
 |
-|
+|approx 140 minutes
 |
 |
@@ Line 101: / Line 101: @@
 |animationcycle04.bfb (Frame 13-14)
 |1.9.
-|approx. 60 minutes
+|
 |Robert S. und Florian M.
 |
-|
+|approx. 60 minutes
 |
 |
@@ Line 115: / Line 115: @@
 |
 |Robert S. und Florian M.
+|
 |approx. 60 minutes
-|
 |
 |
@@ Line 125: / Line 125: @@
 |zoetrope_cap.bfb (cap of the zoetrope)
 |15.9.-16.9.
-|approx. 10 hours till abortion
+|
 |Robert S. und Florian M.
 |
-|
+|approx. 10 hours till abortion
 |
 |imprecise printbed complicates printing of large objects (20x20x1cm), ABS warps too much (high temperature?)
-So große Sachen mit ABS zu drucken ist schwer, versucht PLA --[[User:Matthias.breuer|Matthias.breuer]] 14:37, 22 September 2010 (CEST)
 |optimizing the .stl file, trying the same with PLA
 |[[File:zoe_cap.jpg|right|thumb|150px|]]
@@ Line 138: / Line 137: @@
 |zoetrope_cap.bfb (cap of the zoetrope)
 |21.9.
+|
+|Robert S. und Florian M.
+|
 |approx. 20 minutes
+|
+|problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop
+|
+|no existing image of this try
+|-
+|
+|Eindrucken Variante 2
+|29.09.2010
+|
+|Katharina E.
+|
+|
+|
+|Due to the extensive work needed preparing the LEDs the test print will be the final print.
+|
+|[[File:3DIY LED-eindrucken Variante2 .jpg|right|thumb|150px|]]|-
+|-
+|
+|zoetrope_cap_pla.bfb (cap of the zoetrope with pla settings)
+|28.9.-29.9.
+|
+|Robert S. und Florian M.
+|
+|approx. 8hours
+|
+|structure was a bit week and the material feed was blocked due to mechanical problems with the PLA material roll (approx 30minutes of printing without material(!), cause the extrusion was kind of blocked)
+|slightly higher printing temperature might help, fixing the problems with the material roll will be necessary.
+|[[File:cap.jpg|right|thumb|150px|]]#
+|-
+|
+|zoetrope_lamp.bfb (construction for the led lamp)
+|29.9.
+|
 |Robert S. und Florian M.
 |
+|approx. 2hours
+|
+|everything went perfectly fine
+|
+|[[File:Lamp.jpg|right|thumb|150px|]]
+|-
 |
+|crankhandle_p1.bfb (part of the gear)
+|13.10.
 |
-|problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop
+|Robert S. und Florian M.
+|
+|approx. 20 minutes
+|
+|everything went perfectly fine
+|
+|[[File:Crank_handle_part1.JPG|right|thumb|150px|]]
+|-
+|
+|gearshell.bfb (part of the gear)
+|26.10.
+|
+|Robert S. und Florian M.
 |
+|several hours (only troubleshooting
 |
+|problems with the printbed level (was too close to extruder), flakes of PLA were sometimes extruded together with the ABS
+|leveling the bed, cleaning the extruder
+|no acceptable result, therefore nothing to photography
 |-
+|
+|gearshell2.bfb (part of the gear)
+|9.11.
+|
+|Robert S. und Florian M.
+|
+|approx. 3,5hours
+|
+|everything went perfectly fine
+|
+|[[File:Gearshell.JPG|right|thumb|150px|]]
 |}