GMU:3DIY/Printer queue: Difference between revisions

← Older edit

GMU:3DIY/Printer queue (view source)

Revision as of 21:57, 9 November 2010

2,218 bytes added , 9 November 2010

→‎The printer queue

Olif2166

364

edits

@@ Line 46: / Line 46: @@
 |
 |
-|extremes Warping in der Spitze
+|extreme warping on the spire
-|größerer Ausdruck, Luftzufuhr in der kritischen Phase, Pfeile und Schleifpapier
+|higher print resolution, cooldown by fan in the critical phase, rasp and sand paper
 |[[File:Test_01.jpg|right|thumb|150px|]]
 |-
@@ Line 59: / Line 59: @@
 |
 |
-|verbesserter Testdruck, basierend darauf Ausdrucken des kompletten Animationszyklus aus 16 Einzelbildern
+|improved testprint, based on this, we startet printing the complete animation cycle of 16 frames
 |[[File:Test_02.jpg|right|thumb|150px|]]
 |-
 |
-|animationcycle01.bfb
+|animationcycle01.bfb (Frame 1-4)
 |26.8.
 |
 |Robert S. und Florian M.
 |
+|approx 140 minutes
 |
 |
 |
-|Frame 1-4
+|[[File:Framea.jpg|right|thumb|150px|]]
-|[[File:Animation_01.jpg|right|thumb|150px|]]
 |-
 |
-|animationcycle02.bfb
+|animationcycle02.bfb (Frame 5-7 +12)
 |30.8.
 |
 |Robert S. und Florian M.
 |
+|approx 140 minutes
 |
 |
 |
-|Frame 5-7 +12
+|[[File:Frameb.jpg|right|thumb|150px|]]
-|
 |-
 |
-|animationcycle03.bfb
+|animationcycle03.bfb (Frame 8-11)
 |31.8.
 |
 |Robert S. und Florian M.
 |
+|approx 140 minutes
 |
 |
 |
-|Frame 8-11
+|[[File:Framec.jpg|right|thumb|150px|]]
-|
 |-
 |
-|animationcycle04.bfb
+|animationcycle04.bfb (Frame 13-14)
 |1.9.
 |
 |Robert S. und Florian M.
 |
+|approx. 60 minutes
+|
+|
+|
+|[[File:Framed.jpg|right|thumb|150px|]]
+|-
+|
+|animationcycle05.bfb (Frame 15-16)
+|2.9.
+|
+|Robert S. und Florian M.
 |
+|approx. 60 minutes
 |
 |
-|Frame 13-14
 |
+|[[File:Framee.jpg|right|thumb|150px|]]
 |-
 |
-|animationcycle05.bfb
+|zoetrope_cap.bfb (cap of the zoetrope)
-|2.9.
+|15.9.-16.9.
 |
 |Robert S. und Florian M.
 |
+|approx. 10 hours till abortion
+|
+|imprecise printbed complicates printing of large objects (20x20x1cm), ABS warps too much (high temperature?)
+|optimizing the .stl file, trying the same with PLA
+|[[File:zoe_cap.jpg|right|thumb|150px|]]
+|-
+|
+|zoetrope_cap.bfb (cap of the zoetrope)
+|21.9.
 |
+|Robert S. und Florian M.
 |
+|approx. 20 minutes
 |
-|Frame 15-16
+|problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop
 |
+|no existing image of this try
 |-
 |
-|animationcycle05.bfb
+|Eindrucken Variante 2
-|15.9.-16.9.
+|29.09.2010
+|
+|Katharina E.
+|
+|
+|
+|Due to the extensive work needed preparing the LEDs the test print will be the final print.
+|
+|[[File:3DIY LED-eindrucken Variante2 .jpg|right|thumb|150px|]]|-
+|-
+|
+|zoetrope_cap_pla.bfb (cap of the zoetrope with pla settings)
+|28.9.-29.9.
 |
 |Robert S. und Florian M.
 |
+|approx. 8hours
+|
+|structure was a bit week and the material feed was blocked due to mechanical problems with the PLA material roll (approx 30minutes of printing without material(!), cause the extrusion was kind of blocked)
+|slightly higher printing temperature might help, fixing the problems with the material roll will be necessary.
+|[[File:cap.jpg|right|thumb|150px|]]#
+|-
 |
+|zoetrope_lamp.bfb (construction for the led lamp)
+|29.9.
 |
+|Robert S. und Florian M.
 |
-|Deckel des Zoetrops
+|approx. 2hours
 |
+|everything went perfectly fine
+|
+|[[File:Lamp.jpg|right|thumb|150px|]]
 |-
 |
-|animationcycle05.bfb
+|crankhandle_p1.bfb (part of the gear)
-|15.9.-16.9.
+|13.10.
 |
 |Robert S. und Florian M.
 |
+|approx. 20 minutes
 |
+|everything went perfectly fine
 |
+|[[File:Crank_handle_part1.JPG|right|thumb|150px|]]
+|-
 |
-|Deckel des Zoetrops
+|gearshell.bfb (part of the gear)
+|26.10.
 |
+|Robert S. und Florian M.
+|
+|several hours (only troubleshooting
+|
+|problems with the printbed level (was too close to extruder), flakes of PLA were sometimes extruded together with the ABS
+|leveling the bed, cleaning the extruder
+|no acceptable result, therefore nothing to photography
 |-
+|
+|gearshell2.bfb (part of the gear)
+|9.11.
+|
+|Robert S. und Florian M.
+|
+|approx. 3,5hours
+|
+|everything went perfectly fine
+|
+|[[File:Gearshell.JPG|right|thumb|150px|]]
 |}