Christian Doeller: Conceptual Sensor

From Medien Wiki
Revision as of 16:58, 15 December 2015 by Veja6203 (talk | contribs)


The Improbable Switch



MazeModule.jpg
The Improbable Switch, maze module


For the first assignment I built a switch that needs a (playful) effort to be operated.
It should stretch the time between the different states of change - and it should be allowed to „revolt".

I decided to design a little maze.
In the beginning two little metal balls are positioned at the starting point of the maze.
By that time no current flows through the circuit.
The goal is to make one of the balls fall into the „on-hole“ before the other ball reaches the „off-hole“.
The game is over as soon as one of the balls gets trapped in „hell“.

By activating the „on-hole“ a heart beat sound is turned on.
This sound continues until it is turned off by reaching the „off-hole“.
A loud noise starts buzzing for three seconds when one of the balls is trapped in „hell“.

For a restart both balls need to be removed and the reset-button on the circuit board is to be pushed.


WORK IN PROGRESS

GridSketch.jpg
Sketch for the frame of the maze (10 cm x 10 cm).
Each corridor should have a width of at least 1 cm.

GridSketch1.jpg
Final sketch for the two dimesnional structure of the maze.
Defining pins for connecting the „on“ / „off“ circuit.

Underneath.jpg
Setting up the switch structure with wire and tape.
Adding a connection for the „hell“ - circuit (red).

Paperwalls.jpg
Building the three dimensional wall structure of the maze.
The paper walls are jammed into the sliced Kappafix.

MazeSchematic.jpg
Schematic for the electronics with four 555 Timers:
- monostable mode (trigger) for „on“ and „off“
- astable mode for heart beat sound
- monostable mode (trigger) for „hell“ sound
- astable mode for „hell“ sound (using the same speaker)

MazeBoard.jpg
Circuit borad with reset switch.


RESULT

MazeSetup.jpg



Variable Resistance



SchwammCloseup.jpg
Variable Resistance, modified chalk board


The biggest challenge of Variable Resistance was to find materials that are flexible in terms of the current flowing though them.

We tested things by including them into the circuit of a 555 timers astable mode.

After trying out things that I carried to the classroom I had the idea to connect something to the circuit that was already there.

The chalk board was a good example: by connecting a humid rag (to pin 6) and a piece of wet aluminium foil sticking to the board (to pin 7) I could draw sounds by wiping the surface.

Thereby I found out that it is very important to „calibrate“ the used material: a very high and still hearable tone should sound when the rag is put directly onto the aluminium connector.
By moving the rag further away, the tone will become deeper and deeper (as the resistance rises).
This tone range can be adjusted by turning a potentiometer (between pin 7 and 8) and by trying out different capacitors (between pin 1 and 2).


WORK IN PROGRESS

GridSketch.jpg
Sketch for the frame of the maze (10 cm x 10 cm).
Each corridor should have a width of at least 1 cm.

GridSketch1.jpg
Final sketch for the two dimesnional structure of the maze.
Defining pins for connecting the „on“ / „off“ circuit.

Underneath.jpg
Setting up the switch structure with wire and tape.
Adding a connection for the „hell“ - circuit (red).

Paperwalls.jpg
Building the three dimensional wall structure of the maze.
The paper walls are jammed into the sliced Kappafix.

MazeSchematic.jpg
Schematic for the electronics with four 555 Timers:
- monostable mode (trigger) for „on“ and „off“
- astable mode for heart beat sound
- monostable mode (trigger) for „hell“ sound
- astable mode for „hell“ sound (using the same speaker)

MazeBoard.jpg
Circuit borad with reset switch.


RESULT

MazeSetup.jpg



Variable Resistance