GMU:Designing Utopias: Theory and Practice/Mavie Beisheim - Revision history

Mavie at 20:26, 30 March 2023

2023-03-30T20:26:53Z

← Older revision		Revision as of 20:26, 30 March 2023
Line 151:		Line 151:
	File:Result 6.jpg		File:Result 6.jpg
	</gallery>		</gallery>

			Images by Felipe Cuartas

Mavie at 20:26, 30 March 2023

2023-03-30T20:26:10Z

← Older revision		Revision as of 20:26, 30 March 2023
Line 72:		Line 72:
	*Clothespins		*Clothespins
	*Iron		*Iron

Mavie at 20:24, 30 March 2023

2023-03-30T20:24:47Z

← Older revision		Revision as of 20:24, 30 March 2023
Line 89:		Line 89:
	*Crochet hook		*Crochet hook
	*Needle		*Needle

Mavie at 20:24, 30 March 2023

2023-03-30T20:24:24Z

← Older revision		Revision as of 20:24, 30 March 2023
Line 89:		Line 89:
	*Crochet hook		*Crochet hook
	*Needle		*Needle




	=='''Process'''==		=='''Process'''==

Mavie: /* Top */

2023-03-30T20:23:21Z

Top

← Older revision		Revision as of 20:23, 30 March 2023
Line 82:		Line 82:

	*2 balls of wool		*2 balls of wool



Line 88:		Line 89:
	*Crochet hook		*Crochet hook
	*Needle		*Needle




	=='''Process'''==		=='''Process'''==

Mavie at 20:21, 30 March 2023

2023-03-30T20:21:55Z

← Older revision		Revision as of 20:21, 30 March 2023
Line 88:		Line 88:
	*Crochet hook		*Crochet hook
	*Needle		*Needle




Line 124:		Line 126:
	File:16 Bild.jpg		File:16 Bild.jpg
	</gallery>		</gallery>

Mavie at 20:19, 30 March 2023

2023-03-30T20:19:03Z

← Older revision		Revision as of 20:19, 30 March 2023
Line 45:		Line 45:

	For the top I decided to use wool that covers the loose lattice design with its little threads so you cannot see the underwear so much but it’s still a loose stitch.		For the top I decided to use wool that covers the loose lattice design with its little threads so you cannot see the underwear so much but it’s still a loose stitch.



	==='''Jeans'''===		==='''Jeans'''===
Line 70:		Line 72:
	*Clothespins		*Clothespins
	*Iron		*Iron

Mavie at 20:12, 30 March 2023

2023-03-30T20:12:38Z

Show changes

Mavie at 16:46, 29 November 2022

2022-11-29T16:46:06Z

← Older revision		Revision as of 16:46, 29 November 2022
Line 81:		Line 81:


	LED ist aus, wenn keine Flamme in der Nähe ist und ~~man sieht~~ "No Fire" auf dem Bildschirm.		LED ist aus, wenn keine Flamme in der Nähe ist und "No Fire" erscheint auf dem Bildschirm.

Mavie: Created page with " == '''Flammensensor mit Arduino UNO benutzen''' == '''Was wird benötigt?''' 400px '''Anschlüsse:''' Arduino UNO - Flammensensor G..."

2022-11-29T16:43:50Z

Created page with " == '''Flammensensor mit Arduino UNO benutzen''' == '''Was wird benötigt?''' 400px '''Anschlüsse:''' Arduino UNO - Flammensensor G..."

New page

== '''Flammensensor mit Arduino UNO benutzen''' ==

'''Was wird benötigt?'''

[[File:Zubehör.png|400px]]

'''Anschlüsse:'''

Arduino UNO - Flammensensor
GND - GND
5V - VCC
A0 - A0

'''Code:'''

[[File:Code komplett.png|400px]]

// lowest and highest sensor readings:
const int sensorMin = 0; // sensor minimum
const int sensorMax = 1024; // sensor maximum
void setup() {
// initialize serial communication @ 9600 baud:
Serial.begin(9600);
// initialize digital pin LED_BUILTIN as an output.
pinMode(LED_BUILTIN, OUTPUT);
}

void loop()
// read the sensor on analog A0:
{int sensorReading = analogRead(A0);
// map the sensor range (four options):
// ex: 'long int map(long int, long int, long int, long int, long int)'
int range = map(sensorReading, sensorMin, sensorMax, 0, 3);

// range value:
switch (range) {
case 1: // A fire closer than 5cm away.
Serial.println("Close Fire");
digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level)
delay(1000); // wait for a second
break;
case 2: // No fire detected.
Serial.println("No Fire");
digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW
delay(1000); // wait for a second
break;
}
}

'''Ergebnis:'''

LED ist aus, wenn keine Flamme in der Nähe ist und man sieht "No Fire" auf dem Bildschirm.

[[File:Ohne Flamme.png|400px]]

[[File:No Fire.png|400px]]

LED ist an, wenn eine Flamme in der Nähe ist und auf dem Bildschirm erscheint "Close Fire".

[[File:Mit Flamme.png|400px]]

[[File:Close Fire.png|400px]]