Medien Wiki - User contributions [en]

GMU:DIY-Microscopy/Han

2013-03-29T15:55:19Z

Han: /* pdf Data */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Finding my project ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

[[File:Microscopy-han.JPG|700px]]

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)

Second test shot
<videoflash type="vimeo">55711862|640|480</videoflash>

== Project > Circle < ==

example one scene from movie "sunshine"(danny boyle)
http://www.youtube.com/watch?v=dp7z8Gvexas

[[File:Microscopy-han1.JPG]]

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.

I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

== pdf Data of documentation ==

http://www.uni-weimar.de/medien/wiki/images/DIY_dokumentaion-han.pdf

GMU:DIY-Microscopy/Han

2013-03-29T15:53:07Z

Han: /* Project > Circle < */

File:DIY dokumentaion-han.pdf

2013-03-29T15:44:08Z

Han:

== Summary ==

== Copyright status: ==

== Source: ==

GMU:DIY-Microscopy/Han

2013-03-29T15:36:15Z

Han: /* Finding my project */

GMU:DIY-Microscopy/Han

2013-03-29T15:36:07Z

Han: /* Video of project > Circle < */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Finding my project ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

[[File:Microscopy-han.JPG]]

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)

Second test shot
<videoflash type="vimeo">55711862|640|480</videoflash>

== Project > Circle < ==

example one scene from movie "sunshine"(danny boyle)
http://www.youtube.com/watch?v=dp7z8Gvexas

[[File:Microscopy-han1.JPG]]

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.

I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

File:Microscopy-han1.JPG

2013-03-29T15:23:08Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

GMU:DIY-Microscopy/Han

2013-03-29T15:12:40Z

Han: /* Finding my project */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Finding my project ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

[[File:Microscopy-han.JPG]]

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)

Second test shot
<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T15:11:42Z

Han: /* Finding my project */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Finding my project ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

[[File:Microscopy-han.JPG]]

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T15:08:54Z

Han: /* Second test video */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Finding my project ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

|File

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

File:Microscopy-han.JPG

2013-03-29T15:06:52Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

GMU:DIY-Microscopy/Han

2013-03-29T15:00:54Z

Han: /* test images and video */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:59:52Z

Han: /* completion of camera making */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of Microscope ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

DONE!

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:59:13Z

Han: /* cardboard model */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== Test model from carton and transparent plastic film ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:58:02Z

Han: /* changing camera lens */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== Episode ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

During making of lens i got some problem. a surface of lens is stained with some superglue!!! I tried to erase it. but it was going wrong. so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled ‘eureka’.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:57:15Z

Han: /* making of camera */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== Assembling ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

Because it is not possible to make one outside cover by 3d-printing, and to make a cylinder by laser-cut, I had to find an alternative. Finally I got a frame of ribbon for outside cover(White stick in top-photo). Base of this size I designed inside parts of cover for laser-cutting.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:56:17Z

Han: /* lasercutting design */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

After seeing of 3D printed things I considered that the surface of it is so rough and it can make some rubbing. Therefore I decided to use a laser-cutting machine instead of 3d-printing, because I need a smooth surface between in- and outside cover.

[[File:microscopy-han(lasercutter).jpg|500px]]

A plan to laser-cutting with Adobe Illustrator
(The material is clear acryl with thickness of 3mm)

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:55:18Z

Han: /* cardboard model */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

Focusing of this step is making 2 different cover and function how to be no rubbing.
A gap between them is under 1mm.

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:54:22Z

Han: /* 3D Model */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>
> The second plan - Design with Google sketch up <

As a picture camera is fixed with bottom by 2 legs and I set extra bottom part only for focusing.
Spring is for moving of outside cover up and down. If be turned right, then outside cover goes up. And if be turned left, it goes down because of elasticity of spring.

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-29T14:51:21Z

Han: /* Miroscopy stage construction */

== Making of Microscope ==
> The first plan <
[[File:Scetch microscope han.jpg|500px]]

To control a height in detail, I choose a screw and legs like tripod. Inside of Set #1 I would put into a camera and I thought it can be control a height through turning of legs. To be useful I put into a spring between set #1 and outside frame.
After a while, I found that it could be difficult, impossible to control it.
I had to change a plan.

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-26T01:06:42Z

Han: /* Video of project > Circle < */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

At the second previous test shot(http://vimeo.com/55711862) I set a theme about the creature and birth of everything. I defined the most form of everything of the world is circle, like a somatic and red blood cell and it grows up a planet or the sun. And it is also one of basic form of moment when something created or be born. I look for perfect circle around of us what we can see though our eyes.
I asked myself from where start to create and we came. It can be created by the God or by ourself.

<videoflash type="vimeo">61795628|720|480</videoflash>
A content of narration is genesis 1:1 ~ 31 in Bible

GMU:DIY-Microscopy/Han

2013-03-26T00:26:09Z

Han: /* Second test video */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-03-26T00:25:46Z

Han: /* Second test video */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

I took a picture another objects what I choose and found by myself. There were ice cream, strawberry jam, rotten milk, salt, urine, blood. Then I mixed 2 things of that. Clay and dish soap, jam and milk, salt and papper. On its way I tried to mix a milk and olive oil but it didn’t and separated each other. And they have shown something special to me. A bubble and a drop of milk in olive oil have moved very slowly and silky. A form of that is perfect circle.

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany.
I give a title "cell division". I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)
Second test shot

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-03-26T00:25:10Z

Han: /* Video of project > Circle < */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany. I give a title "cell division". Water bubble with black watercolor in olive oil. I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-03-26T00:24:49Z

Han: /* Second test video */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany. I give a title "cell division". Water bubble with black watercolor in olive oil. I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)

<videoflash type="vimeo">55711862|640|480</videoflash>

== Video of project > Circle < ==

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-03-26T00:18:42Z

Han: /* Concept video 2012/13 */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Second test video ==

Second test video of class 'DIY-Microscopy' at Bauhaus Uni Weimar, Germany. I give a title "cell division". Water bubble with black watercolor in olive oil. I have shaken hard one drop of water with black watercolor in olive oil and it is divided finely. After a while it's started to merge together.
Edited on reverse and regulated speed. (Origin length of video is 36min.)

<videoflash type="vimeo">55711862|640|480</videoflash>

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

== Video of project > Circle < ==

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-03-24T17:00:13Z

Han: /* Concept video 2012/13 */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Concept video 2012/13 ==
Concept video of class 'DIY-Microscopy' in Bauhaus-Uni Weimar, Germany.
I give a title "cell division"
Water bubble with black watercolour in olive oil.
I shaked hard a drop of water with black watercolour in olive oil and it is devided finely. After a while it's started to merge together.

Edited in reverse and regulated speed.
(Origin length of video is 36min.)

<videoflash type="vimeo">55711862|640|480</videoflash>

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

== Video of project > Circle < ==

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-03-24T16:58:11Z

Han: /* Concept video 2012/13 */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Concept video 2012/13 ==
Concept video of class 'DIY-Microscopy' in Bauhaus-Uni Weimar, Germany.
I give a title "cell division"
Water bubble with black watercolour in olive oil.
I shaked hard a drop of water with black watercolour in olive oil and it is devided finely. After a while it's started to merge together.

Edited in reverse and regulated speed.
(Origin length of video is 36min.)

<videoflash type="vimeo">55711862|640|480</videoflash>

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

== Video of project > Circle <

<videoflash type="vimeo">61795628|720|480</videoflash>

GMU:DIY-Microscopy/Han

2013-01-14T09:54:25Z

Han: /* Concept video 2012/13 */

== Miroscopy stage construction ==
[[File:Scetch microscope han.jpg|500px]]

== 3D Model ==
<gallery>
File:sketch 3d han1.jpg|
File:sketch 3d han2.jpg|
File:sketch 3d han3.jpg|
File:sketch 3d han4.jpg|
</gallery>

== cardboard model ==
<gallery>
File:Hardboard-han1.JPG|
File:Hardboard-han2.JPG|
File:Hardboard-han3.JPG‎|

</gallery>

== changing camera lens ==
<gallery>
File:Camera-han.JPG |
File:Snapshot 2.jpg|
</gallery>

during making of lens i got some problem. a surface of lens is stained with some superglue!!! i tried to erase it. but it was going wrong.
so i change my mind... i broke a lens. i thought it is just protect-lens and for wide angle. but i also worried to be worst myself. i hope one eureka! or buy new thing.

and then i yelled eureka.

== lasercutting design ==

[[File:microscopy-han(lasercutter).jpg|500px]]

a material is clear acryl with thickness of 3mm

== making of camera ==

<gallery>
File:making1 han.jpg|
File:making2 han.jpg|
File:making3 han.jpg|
</gallery>

instead of 3d printing i choose another parts to hold a camera body parts.
white thing in photo is a frame of gift ribbon. i got at mac geiz in artrium.
so i designed every parts from a size of that frame.

== completion of camera making ==

<gallery>
File:camera1 han.jpg|
File:camera2 han.jpg|
File:camera3 han.jpg|
File:camera4 han.jpg|
</gallery>

== test images and video ==
<gallery>
File:onion skin1.jpg|image captions
File:onion skin 2.jpg|image captions
File:leaf2.jpg|image captions
File:leaf3.jpg|image captions
File:hair.jpg|image captions
File:earwax from cat1.jpg|image captions
File:earwax from cat 1-1.jpg|image captions
File:skin from finger.jpg|image captions
File:spit.jpg|image captions
</gallery>

The first group of object for a test shot is things around me and info-guide from Max. Handy screen, wings of a deaf bugs, soil, leaves, hair, skin of onion and from my lips, spit, earwax from my cat etc. And i got some problems about a lighting. it needs to make it better.

I choose freeware webcam program 'Debut video capture software'.
http://www.nchsoftware.com/capture/index.html
It can be controlled easier and with more tools to take a better video.

<videoflash type="vimeo">54235417|640|480</videoflash>

== Concept video 2012/13 ==
Concept video of class 'DIY-Microscopy' in Bauhaus-Uni Weimar, Germany.
I give a title "cell division"
Water bubble with black watercolour in olive oil.
I shaked hard a drop of water with black watercolour in olive oil and it is devided finely. After a while it's started to merge together.

Edited in reverse and regulated speed.
(Origin length of video is 36min.)

<videoflash type="vimeo">55711862|640|480</videoflash>

example one scene from movie "sunshine"(danny boyle)

http://www.youtube.com/watch?v=dp7z8Gvexas

GMU:DIY-Microscopy/Han

2012-12-17T00:06:42Z

Han: /* Concept video 2012/13 */

GMU:DIY-Microscopy/Han

2012-12-16T23:23:14Z

Han: /* test images and video */

GMU:DIY-Microscopy/Han

2012-11-25T21:59:37Z

Han: /* lasercutting design */

GMU:DIY-Microscopy/Han

2012-11-25T18:47:14Z

Han: /* completion of camera making */

File:Spit.jpg

2012-11-25T18:21:42Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Earwax from cat 1-1.jpg

2012-11-25T18:21:23Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Skin from finger.jpg

2012-11-25T18:20:47Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Earwax from cat 2.jpg

2012-11-25T18:20:23Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Earwax from cat1.jpg

2012-11-25T18:19:27Z

Han:

== Summary ==

== Copyright status: ==

== Source: ==

File:Hair.jpg

2012-11-25T18:19:15Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Leaf3.jpg

2012-11-25T18:18:52Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Leaf2.jpg

2012-11-25T18:18:36Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Leaf1.jpg

2012-11-25T18:18:01Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Onion skin 2.jpg

2012-11-25T18:17:38Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

GMU:DIY-Microscopy/Han

2012-11-25T18:16:44Z

Han: /* lasercutting design */

File:Onion skin1.jpg

2012-11-25T18:16:38Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Camera4 han.jpg

2012-11-25T18:04:42Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Camera3 han.jpg

2012-11-25T18:04:24Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Camera2 han.jpg

2012-11-25T18:04:04Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Camera1 han.jpg

2012-11-25T18:03:46Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Making3 han.jpg

2012-11-25T18:03:26Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==

File:Making2 han.jpg

2012-11-25T18:03:05Z

Han:

== Summary ==

== Copyright status: ==

== Licensing ==
{{self|cc-by-sa-nc-3.0}}
== Source: ==